Rose-electronics Porter Manual do Utilizador Página 1

Porter Code activated switch 10707 Stancliff Road Phone:

6 PORTER INSTALLATION AND OPERATIONS MANUAL Quick set-up Serial Porter 1. Connect your computer terminal to port 0 with the proper cable. Refe

PORTER INSTALLATION AND OPERATIONS MANUAL 7 Parallel Porter 1. Cable your devices to ports 1-4 (or 8) with a straight-through cable that has male

Installation 8 PORTER INSTALLATION AND OPERATIONS MANUAL You should have received the Porter switch unit and a power adapter that connects to t

Configuration PORTER INSTALLATION AND OPERATIONS MANUAL 9 After installing the Porter, it must be configured to match the protocol for your equipm

10 PORTER INSTALLATION AND OPERATIONS MANUAL The range option will set any changed item(s) (i.e. baud rate, parity, etc.) to the new common val

PORTER INSTALLATION AND OPERATIONS MANUAL 11 Change prefix This option allows changing of the Porter’s prefix. As shipped, the unit’s prefix is s

12 PORTER INSTALLATION AND OPERATIONS MANUAL Change command purge timeout The command purge timeout determines whether to treat a partial prefi

PORTER INSTALLATION AND OPERATIONS MANUAL 13 Configuration of Parallel Units The Centronics parallel interface is usually implemented consistently

Power Up Tests 14 PORTER INSTALLATION AND OPERATIONS MANUAL Power Up Initial Display Push in the power switch to turn the unit on. Porter goes

PORTER INSTALLATION AND OPERATIONS MANUAL 15 If it does it indicates that possibly the unit has been subjected to a strong static discharge or sur

Operation 16 PORTER INSTALLATION AND OPERATIONS MANUAL Initial state Following the successful completion of its power up test, the Porter turns

PORTER INSTALLATION AND OPERATIONS MANUAL 17 Broadcast mode When the <prefix>B broadcast mode command is entered, all ports enabled for broa

18 PORTER INSTALLATION AND OPERATIONS MANUAL The manual mode can be used to exit the null destination state, but it cannot be used to set the u

PORTER INSTALLATION AND OPERATIONS MANUAL 19 Front Panel The front panel is useful for observing the status of the Porter and manually changing th

20 PORTER INSTALLATION AND OPERATIONS MANUAL Porter Commands The command codes shown below control various functions of the Porter. All codes

PORTER INSTALLATION AND OPERATIONS MANUAL 21 Connect commands 1-8 The connect commands allow selection of the current port connection. Commands 5

22 PORTER INSTALLATION AND OPERATIONS MANUAL Format codes by bit Character w: bits 15 - 12 Bits 15 – 14 00 = Odd parity 01 = Even parity 10 =

PORTER INSTALLATION AND OPERATIONS MANUAL 23 Format codes by bit for 38400 baud option Character w: bits 15 - 12 Bits 15 – 14 00 = Odd parity 01

24 PORTER INSTALLATION AND OPERATIONS MANUAL Set Initial destination command This command is used to set the initial destination the Porter sel

PORTER INSTALLATION AND OPERATIONS MANUAL 25 Ready (Check DSR) command This command allows a program to determine if a given serial port’s DSR (pi

Limited Warranty Copyright 1986-1991 Rose Electronics. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or

26 PORTER INSTALLATION AND OPERATIONS MANUAL Applications Buffering The switch may have a buffer of 16, 64, or 256 Kbytes of memory. The memor

PORTER INSTALLATION AND OPERATIONS MANUAL 27 Diagnostic You can execute some special diagnostic tests to determine if the Porter has any problems.

28 PORTER INSTALLATION AND OPERATIONS MANUAL Test 3 – Static ram read/write test This test is the same as in the ‘Short Test’ Test 4 – Non-vola

PORTER INSTALLATION AND OPERATIONS MANUAL 29 Table VI Diagnostic LED Error Display Legend: M=Mode LED D=Data LED B=Busy LED E=Error L

30 PORTER INSTALLATION AND OPERATIONS MANUAL Table VII Loopback Test Connectors Porter parallel loopback connector Porter se

PORTER INSTALLATION AND OPERATIONS MANUAL 31 Appendix A – Porter Pin outs Serial model Pin Signal Name Abbrv. I/ODescription 2 Transmit data TXD O

32 PORTER INSTALLATION AND OPERATIONS MANUAL Serial Model with / 422 option Pin Signal Name Direction Description 1 Chassis Ground Common Co

PORTER INSTALLATION AND OPERATIONS MANUAL 33 Appendix B – Cable Pin outs The diagrams below show the Porter’s pin out on the left and all other de

34 PORTER INSTALLATION AND OPERATIONS MANUAL Appendix C – Specifications Interface Specifications Serial models Electrical: RS232 + 9 and -9

Table of Contents Contents Introduction ...

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 Internet: WWW.ROSE.COM

Introduction PORTER INSTALLATION AND OPERATIONS MANUAL 1 Introduction This manual contains information for the installation and operation of the Po

Getting Started 2 PORTER INSTALLATION AND OPERATIONS MANUAL First Steps Congratulations! You have chosen one of the best code activated switche

MODELS PORTER INSTALLATION AND OPERATIONS MANUAL 3 Front panel Indicators Description Power Status Mode Data Busy Error Po

4 PORTER INSTALLATION AND OPERATIONS MANUAL Rear panel (Serial model) Connectors Description Port 0 Ports 1-8 Power input DB25F – Co

PORTER INSTALLATION AND OPERATIONS MANUAL 5 Rear panel (Parallel model) Connectors Description Port 0 Ports 1-8 Power input Centronics