Rose electronics UC2-1x16U/E Manual de Instruções descarregar pdf (Página 18)

12 ULTRACONSOLE INSTALLATION AND OPERATIONS MANUAL

The “Starting computer” number will depend on which Unit is being configured. The “Starting computer” number for

the first Unit is always one (default). Using Units that have 16 CPU ports, the “Starting computer” number for the

second Unit is the total number of CPU ports on the first Unit + one or 17, the third Unit would have a “Starting

computer” number of 33 (Total CPU ports on unit #1 and unit #2 + 1, and so on.

Maximum computers

The “Maximum computers” value is calculated by counting the total number of CPU ports on all units. If your system

consists of 10 UltraConsole Units, each with 16 CPU ports, the “Maximum computers” number would be 160. The

“Maximum computers” value must be entered from a KVM station and when saved, this value is propagated to all

connected Units.

Connecting the expansion units

The installation steps below are for all UltraConsole models.

Steps:

(NOTE: Expansion cables should not be connected at this point)

1. Verify that power is “OFF” on all UltraConsole switches.

2. Configure the “Starting computer” number for all the UltraConsole switches, starting with Unit #2 by:

(Unit #1 default = 1)

a. Connect a KVM station to Unit #2’s KVM connector using the appropriate KVM adapter cable.

b. Apply power to the KVM monitor and to UltraConsole #2.

c. When the internal diagnostic completes, press and release the left control [Ctrl] key, then the F12 key to

display the “Main menu”.

d. Select “System” and press [Enter].

e. Next, select “Starting computer number” and press [Enter]. An input box will display for a new starting

computer number. Enter the correct “Starting computer” number for this Unit (See page 15) and press

[Enter].

f. Press the “Esc” key to return to the “Main menu”.

g. Select “Save” and press [Enter]. A “YES/NO” choice box will display. Select “YES” and press [Enter] to save

the changes.

h. Turn the power off on the UltraConsole.

i. Connect the KVM station to the KVM connector on Unit #3.

j. Configure this Units “Starting computer” number and then all other Units in the system. When the “Starting

computer” number has been entered for all Units, proceed to step 3.

3. Connect the KVM station to Unit #1’s KVM connector and apply power to the monitor and Unit #1.

4. Enter the “Maximum computers” number

a. Display the main menu (left control [Ctrl] key, then the F12 key.)

b. Select “System” and press [Enter].

c. Select “Maximum computers” and press [Enter]. An input box will display for a new “Maximum computers”

number. Enter the correct “Maximum computers” value as explained on page 15 and press [Enter].

d. Press the “Esc” key to return to the “Main menu”, select “Save” and press [Enter]. A “YES/NO” choice box

will display. Select “YES” and press [Enter] to save the change.

5. The next item is to connect the Units in a “BUS” configuration and verify that communication between the Units is

established. To do this, call up the System status display by pressing and releasing the left control [Ctrl] key,

then the F12 key.

6. Select “Status” from the Main menu and press [Enter]. The system status screen will display showing the

following: (Figure 13)

a. Computers

b. Power (Power on status)

c. POS (Card position)

d. VER (Program version)

e. KVM

f. CPU

g. User

h. Status

The number of system CPU ports that Unit #1 has will be highlighted. If the Unit is a 16-port switch, computers 1–4,

5–8, 9–12, and 13–16 will be highlighted on the status screen.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 61 62

Comentários a estes Manuais

Sem comentários

Rose electronics UC2-1x16U/E Manual de Instruções Página 18

Comentários a estes Manuais

Manuais e produtos relacionados com Interruptores KVM Rose electronics UC2-1x16U/E